CFD-Based Thermohydrodynamic Analysis of Vegetable Oil Lubricants in Journal Bearings
DOI:
https://doi.org/10.26877/asset.v8i3.3607Keywords:
journal bearing, biolubricant, load-carrying capacityAbstract
This study investigates the thermohydrodynamic performance of journal bearings lubricated with palm trimethylolpropane (TMP) ester as a biolubricant, compared to conventional engine oil, using computational fluid dynamics (CFD) in ANSYS Fluent. The objective is to evaluate the influence of lubricant type on pressure distribution, load carrying capacity, friction force, and cavitation behavior. The results show that palm TMP ester generates higher hydrodynamic pressure while maintaining a similar pressure distribution pattern to engine oil. The load carrying capacity increases significantly by approximately 493% at 48 rad/s and 343% at 68 rad/s compared to engine oil. However, this improvement is accompanied by an increase in friction force of about 280% and 234% at the respective speeds due to higher viscosity. In addition, the vapor volume fraction ranges from 0.69 to 0.73, indicating cavitation, with palm TMP ester showing a slightly higher tendency. These findings demonstrate a trade-off between enhanced load support and increased friction, highlighting the potential of palm TMP ester as an environmentally friendly lubricant for hydrodynamic bearing applications.
References
[1] Kyrkou ME, Nikolakopoulos PG. Simulation of thermo-hydrodynamic behavior of journal bearings, lubricating with commercial oils of different performance. Simul Model Pract Theory 2020;104. https://doi.org/10.1016/j.simpat.2020.102128.
[2] Jang JY, Khonsari MM. On the thermohydrodynamic performance of aerated lubricants in steadily- and dynamically-loaded journal bearings. Tribol Int 2022;173. https://doi.org/10.1016/j.triboint.2022.107606.
[3] Gethin DT. Modelling the thermohydrodynamic behaviour of high speed journal bearings. vol. 29. 1996.
[4] Dal A, Şahin M, Kiliç M. A thermohydrodynamic performance analysis of a fluid film bearing considering with geometrical parameters. Journal of Thermal Engineering 2023;9:1604–17. https://doi.org/10.18186/THERMAL.1401279.
[5] Chasalevris A, Gavalas I, Sawicki JT. Optimal bearing configuration selection for power generation shaft-trains: A linear and nonlinear dynamics approach. J Sound Vib 2025;599. https://doi.org/10.1016/j.jsv.2024.118907.
[6] Nikolic N, Antonic Z, Doric J, Ruzic D, Galambos S, Jocanovic M, et al. An analytical method for the determination of temperature distribution in short journal bearing oil film. Symmetry (Basel) 2020;12. https://doi.org/10.3390/SYM12040539.
[7] Fillon M, Bouyer J. Thermohydrodynamic analysis of a worn plain journal bearing. Tribol. Int., vol. 37, 2004, p. 129–36. https://doi.org/10.1016/S0301-679X(03)00051-3.
[8] Dousti S, Allaire P. A thermohydrodynamic approach for single-film and double-film floating disk fixed thrust bearings verified with experiment. Tribol Int 2019;140. https://doi.org/10.1016/j.triboint.2019.105858.
[9] Lin X, Jiang S, Zhang C, Liu X. Thermohydrodynamic analysis of high speed water-lubricated spiral groove thrust bearing considering effects of cavitation, inertia and turbulence. Tribol Int 2018;119:645–58. https://doi.org/10.1016/j.triboint.2017.11.037.
[10] Li B, Sun J, Zhu S, Fu Y, Zhao X, Wang H, et al. Thermohydrodynamic lubrication analysis of misaligned journal bearing considering the axial movement of journal. Tribol Int 2019;135:397–407. https://doi.org/10.1016/j.triboint.2019.03.031.
[11] Chun SM. Thermohydrodynamic lubrication analysis of high-speed journal bearing considering variable density and variable specific heat. Tribol Int 2004;37:405–13. https://doi.org/10.1016/j.triboint.2003.12.009.
[12] Tauviqirrahman M, Muthik B, Muchammad M, Pratomo AW, Jamari J. Effect of cavitation modelling on the prediction of the lubrication performance using CFD: A case study of journal bearing lubricated with non-newtonian. International Journal of Engineering and Technology 2016;8:2541–6. https://doi.org/10.21817/ijet/2016/v8i6/160806207.
[13] Neta MMFM, Monteiro RRC, Ribeiro Filho PRCF, Cavalcante CL, Luna FMT. Tribological Properties of Biolubricants: A Comprehensive Bibliometric and Trend Analysis. Lubricants 2026;14:77. https://doi.org/10.3390/lubricants14020077.
[14] Hussain MM, Pratap AP, Gaval VR. Study of vegetable oil based biolubricants and its hydrodynamic journal bearing application: A review. Tribology in Industry 2021;43:511–23. https://doi.org/10.24874/ti.979.10.20.02.
[15] Rasep Z, Noor M, Witri A, Yazid M, Samion S. A study of cavitation effect in a journal bearing using CFD: A case study of engine oil, palm oil and water. vol. 28. 2021.
[16] Rasep Z, Muhammad Yazid MNAW, Samion S. Lubrication of textured journal bearing by using vegetable oil: A review of approaches, challenges, and opportunities. Renewable and Sustainable Energy Reviews 2021;146. https://doi.org/10.1016/j.rser.2021.111191.
[17] Hammza TM, Rasheid Hmoad N, Abdulkareem AA. Effect of Using the Biolubricant Oil on the Dynamic Performance of Journal Bearings. vol. 20. 2020.
[18] Quinchia LA, Delgado MA, Reddyhoff T, Gallegos C, Spikes HA. Tribological studies of potential vegetable oil-based lubricants containing environmentally friendly viscosity modifiers. Tribol Int 2014;69:110–7. https://doi.org/10.1016/j.triboint.2013.08.016.
[19] Mohammed MS, Kassab SZ, El-Maghlany WM, Elhadary M, Badawi MB. Thermo-hydrodynamic analysis of plain journal bearings: comparative study of ionic liquids and conventional oil lubricants. Thermal Science and Engineering Progress 2025;65. https://doi.org/10.1016/j.tsep.2025.103919.
[20] Kamarapu SK, Amarnath M, Tiwari S. Nanoenhanced biolubricant for improving lubrication in roller bearing steel-steel contact surfaces - a comparative tribological study. Diam Relat Mater 2025;154. https://doi.org/10.1016/j.diamond.2025.112160.
[21] Xie M, Tan H, Zhao G. A clean and sustainable strategy to produce bio-lubricant with high-bearing and good anti-oxidation ability from Lanzhou lily. J Clean Prod 2022;371. https://doi.org/10.1016/j.jclepro.2022.133333.
[22] Pawar R V., Hulwan DB. Rheological and tribological evaluation of sustainable biolubricants derived from Jatropha and Karanja oils for crankshaft bearing applications. Tribol Int 2025;211. https://doi.org/10.1016/j.triboint.2025.110875.
[23] Taghipour Y, Akbarzadeh P, Moradgholi F, Eftekhari Yazdi M. Numerical study of the cavitation effect on plain bearings in constant and variable viscosity states. Meccanica 2021;56:2507–16. https://doi.org/10.1007/s11012-021-01391-7.
[24] Heikal EK, Elmelawy MS, Khalil SA, Elbasuny NM. Manufacturing of environment friendly biolubricants from vegetable oils. Egyptian Journal of Petroleum 2017;26:53–9. https://doi.org/10.1016/j.ejpe.2016.03.003.
[25] Kamat H, Kini CR, Shenoy SB. Effect of Cavitation and Temperature on Fluid Film Bearing Using CFD and FSI Technique: A Review. Archives of Computational Methods in Engineering 2023;30:1623–36. https://doi.org/10.1007/s11831-022-09847-z.
[26] Li SS, Lu YX, Dong ML, Shao J, Yu F. Modeling and analysis of high-speed journal bearing based on thermal hydrodynamic lubrication theory. Applied Mechanics and Materials, vol. 380–384, 2013, p. 82–6. https://doi.org/10.4028/www.scientific.net/AMM.380-384.82.
[27] Meng FM, Zhang L, Liu Y, Li TT. Effect of compound dimple on tribological performances of journal bearing. Tribol Int 2015;91:99–110. https://doi.org/10.1016/j.triboint.2015.06.030.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Advance Sustainable Science Engineering and Technology
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
